Vintage Wheels (1/3, 1/4, 1/5, 1/6, 1/8 Scale)
Now you can build that vintage aircraft you've always wanted to. Our scale vintage wheels come in five sizes, 1/3 scale (9.33"), 1/4 scale (7"), 1/5 scale (5.60") 1/6 scale (4.66"), and 1/8 scale (3.50") and are made of lightweight solid foam material which is very durable. The Vintage series was designed from actual wheels of WWI and other early aircraft. Internally, the tire is secured to the hub which is paintable ABS plastic. The axle diameter is 1/8" and can be drilled out to 3/16".
Each wheel weighs approx. 32 grams. 2/pkg.
Cat. No. 350v, 466v

IN-LINE FUEL CONNECTOR

Built in plug is perfect for preventing fuel from flowing into your engine while transporting your model.

Once you are ready to run, simply re-connect the fuel tubing back in-line. Note: This fitting can also be used on the pressure line (line to muffler) and overflow line. 2/pkg.

IN-LINE FUEL CONNECTOR

MICRO BALL LINK

MINI E/Z LINK
FOR .062
Snap fit on to .062" wire, simply bend 90 degree angle on pushrod and install Mini E/Z Link on to pushrod (no Z Bend required). Super lightweight design, ideal for indoor, park flyers and 1/2A aircraft. 0.06 grams/ea. approx. 4/pkg.

MINI PUSH ROD SYSTEM
FOR .062
Our 30" Mini Pushrod System comes complete with (2) .062" pushrods, (2) pushrod housings, (2) Mini E/Z Links (90 degree is already on pushrod) and (2) E/Z Connectors. Ideal for indoor, park flyers and 1/2A aircraft. 36 grams

MICRO SERVO ARM XL

AT LAST, servo arms long enough for the extra throw needed on the electric 3D airplanes! The DU-BRO Micro Servo Arm XL includes (4) single arms, as well as (2) double arms. These arms have had extra special attention given to weight, strength and performance. Made from 100% virgin nylon, they can stand up to the stress of 3D aerobatics and still remain lightweight. The arms measure 1" from the center to the outer edge.The Micro Servo Arm XL comes in (5) different versions to accommodate various micro servos on the market.This version works on the following servos:Hitec HS-56HB, HS-65HB, HS65MG

Micro Steerable Tail Wheel
The Micro Steerable Tail Wheel comes with the strut and a 1/2” dia. wheel. This mount can be steerable or left free to travel. Mounts directly to the tail of your aircraft with CA (cyanoacrylate) or epoxy. The arm for steering is included and is 1 1/16” wide. This unit is paintable ABS plastic and will add functionality to your aircraft without adding a lot of weight. 1/pkg. (1.75 grams/ea.)

Cat. No. 926

Hatch Latch
A low profile design with a small spring locking latch for any doors, hatches, panels, etc. The Hatch Latch is secured in place using CA (cyanoacrylate). The unit is approx. 1” long X 3/8” wide. Can be painted.1/pkg. (0.75 grams/ea.)

Cat. No. 925

E/Z Glo™ Glo-Plug Ignitor & Tester (1/pkg.)
This is a revolutionary ignitor and glo-plug tester. The E/Z Gloª will not only effectively ignite your models glo-plug, but will also test it and report its condition with an audible beep. Simply connect the E/Z Glo to your glo-plug, press the test button and listen for the beep. If you hear a beep, the plug is good. If there is no beep, the plug is bad. The E/Z Gloª comes with a 1700 mAh battery & charger.

Cat. No. 927